# 4.2.4.3. Input Files¶

Users specify the blade model parameters; including its geometry, cross-sectional properties, and FE and output control parameters; via a primary BeamDyn input file and a blade property input file. When used in stand-alone mode, an additional driver input file is required. This driver file specifies inputs normally provided to BeamDyn by FAST, including simulation range, root motions, and externally applied loads.

No lines should be added or removed from the input files, except in tables where the number of rows is specified.

## 4.2.4.3.1. Units¶

BeamDyn uses the SI system (kg, m, s, N). Angles are assumed to be in radians unless otherwise specified.

## 4.2.4.3.2. BeamDyn Driver Input File¶

The driver input file is needed only for the stand-alone version of BeamDyn. It contains inputs that are normally set by FAST and that are necessary to control the simulation for uncoupled models.

The driver input file begins with two lines of header information, which is for the user but is not used by the software. If BeamDyn is run in the stand-alone mode, the results output file will be prefixed with the same name of this driver input file.

A sample BeamDyn driver input file is given in Section 4.2.4.8.1.

### 4.2.4.3.2.1. Simulation Control Parameters¶

DynamicSolve is a logical variable that specifies if BeamDyn should use dynamic analysis (DynamicSolve = true) or static analysis (DynamicSolve = false). t_initial and t_final specify the starting time of the simulation and ending time of the simulation, respectively. dt specifies the time step size.

### 4.2.4.3.2.2. Gravity Parameters¶

Gx , Gy , and Gz specify the components of gravity vector along $$X$$, $$Y$$, and $$Z$$ directions in the global coordinate system, respectively. In FAST, this is normally 0, 0, and -9.80665.

### 4.2.4.3.2.3. Inertial Frame Parameters¶

This section defines the relation between two inertial frames, the global coordinate system and initial blade reference coordinate system. GlbPos(1), GlbPos(2), and GlbPos(3) specify three components of the initial global position vector along $$X$$, $$Y$$, and $$Z$$ directions resolved in the global coordinate system, see Figure Fig. 4.25. And the following $$3 \times 3$$ direction cosine matrix (GlbDCM) relates the rotations from the global coordinate system to the initial blade reference coordinate system.

Fig. 4.25 Global and blade coordinate systems in BeamDyn.

### 4.2.4.3.2.4. Blade Floating Reference Frame Parameters¶

This section specifies the parameters that define the blade floating reference frame, which is a body-attached floating frame; the blade root is cantilevered at the origin of this frame. Based on the driver input file, the floating blade reference fame is assumed to be in a constant rigid-body rotation mode about the origin of the global coordinate system, that is,

(4.57)$v_{rt} = \omega_r \times r_t$

where $$v_{rt}$$ is the root (origin of the floating blade reference frame) translational velocity vector; $$\omega_r$$ is the constant root (origin of the floating blade reference frame) angular velocity vector; and $$r_t$$ is the global position vector introduced in the previous section at instant $$t$$, see Fig. 4.25. The floating blade reference frame coincides with the initial floating blade reference frame at the beginning $$t=0$$. RootVel(4), RootVel(5), and RootVel(6) specify the three components of the constant root angular velocity vector about $$X$$, $$Y$$, and $$Z$$ axises in global coordinate system, respectively. RootVel(1), RootVel(2), and RootVel(3), which are the three components of the root translational velocity vector along $$X$$, $$Y$$, and $$Z$$ directions in global coordinate system, respectively, are calculated based on Eq. (4.57).

BeamDyn can handle more complicated root motions by changing, for example, the BD_InputSolve subroutine in the Driver_Beam.f90 (requiring a recompile of stand-alone BeamDyn).

The blade is initialized in the rigid-body motion mode, i.e., based on the root velocity information defined in this section and the position information defined in the previous section, the motion of other points along the blade are initialized as

(4.58)$\begin{split}a_{0} &= \omega_r \times (\omega_r \times (r_0 + P)) \\ v_0 &= v_{r0} + \omega_r \times P \\ \omega_0 &= \omega_r\end{split}$

where $$a_{0}$$ is the initial translational acceleration vector along the blade; $$v_0$$ and $$\omega_0$$ the initial translational and angular velocity vectors along the blade, respectively; and $$P$$ is the position vector along the blade relative to the root. Note that these equations are actually implemented with a call to the NWTC Library’s mesh mapping routines.

This section defines the applied loads, including distributed, point (lumped), and tip-concentrated loads, for the stand-alone analysis.

The first six entries DistrLoad(i), $$i \in [1,6]$$, specify three components of uniformly distributed force vector and three components of uniformly distributed moment vector in the global coordinate systems, respectively.

The following six entries TipLoad(i), $$i \in [1,6]$$, specify three components of concentrated tip force vector and three components of concentrated tip moment vector in the global coordinate system, respectively.

NumPointLoads defines how many point loads along the blade will be applied. The table following this input contains two header lines with seven columns and NumPointLoads rows. The first column is the non-dimensional distance along the local blade reference axis, ranging from $$[0.0,1.0]$$. The next three columns, Fx, Fy, and Fz specify three components of point-force vector. The remaining three columns, Mx, My, and Mz specify three components of a moment vector.

The distributed load defined in this section is assumed to be uniform along the blade and constant throughout the simulation. The tip load is a constant concentrated load applied at the tip of a blade.

It is noted that all the loads defined in this section are dead loads, i.e., they are not rotating with the blade following the rigid-body rotation defined in the previous section.

BeamDyn is capable of handling more complex loading cases, e.g., time-dependent loads, through customization of the source code (requiring a recompile of stand-alone BeamDyn). The user can define such loads in the BD_InputSolve subroutine in the Driver_Beam.f90 file, which is called every time step. The following section can be modified to define the concentrated load at each FE node:

u%PointLoad%Force(1:3,u%PointLoad%NNodes)  = u%PointLoad%Force(1:3,u%PointLoad%NNodes)  + DvrData%TipLoad(1:3)


where the first index in each array ranges from 1 to 3 for load vector components along three global directions and the second index of each array ranges from 1 to u%PointLoad%NNodes, where the latter is the total number of FE nodes. Note that u%PointLoad%Force(1:3,:) and u%PointLoad%Moment(1:3,:) have been populated with the point-load loads read from the BeamDyn driver input file using the call to Transfer_Point_to_Point earlier in the subroutine.

For example, a time-dependent sinusoidal force acting along the $$X$$ direction applied at the $$2^{nd}$$ FE node can be defined as

u%PointLoad%Force(:,:) = 0.0D0


with 1.0D+03 being the amplitude and 6.0 being the period. Note that this particular implementation overrides the tip-load and point-loads defined in the driver input file.

Similar to the concentrated load, the distributed loads can be defined in the same subroutine

DO i=1,u%DistrLoad%NNodes
ENDDO


where u%DistrLoad%NNodes is the number of nodes input to BeamDyn (on the quadrature points), and DvrData%DistrLoad(:) is the constant uniformly distributed load BeamDyn reads from the driver input file. The user can modify DvrData%DistrLoad(:) to define the loads based on need.

We note that the distributed loads are defined at the quadrature points for numerical integrations. For example, if Gauss quadrature is chosen, then the distributed loads are defined at Gauss points plus the two end points of the beam (root and tip). For trapezoidal quadrature, p%ngp stores the number of trapezoidal quadrature points.

### 4.2.4.3.2.6. Primary Input File¶

InputFile is the file name of the primary BeamDyn input file. This name should be in quotations and can contain an absolute path or a relative path.

## 4.2.4.3.3. BeamDyn Primary Input File¶

The BeamDyn primary input file defines the blade geometry, LSFE-discretization and simulation options, output channels, and name of the blade input file. The geometry of the blade is defined by key-point coordinates and initial twist angles (in units of degree) in the blade local coordinate system (IEC standard blade system where $$Z_r$$ is along blade axis from root to tip, $$X_r$$ directs normally toward the suction side, and $$Y_r$$ directs normally toward the trailing edge).

The file is organized into several functional sections. Each section corresponds to an aspect of the BeamDyn model.

A sample BeamDyn primary input file is given in Section 4.2.4.8.

The primary input file begins with two lines of header information, which are for the user but are not used by the software.

### 4.2.4.3.3.1. Simulation Controls¶

The user can set the Echo flag to TRUE to have BeamDyn echo the contents of the BeamDyn input file (useful for debugging errors in the input file).

The QuasiStaticInit flag indicates if BeamDyn should perform a quasi-static solution at initialization to better initialize its states. In general, this should be set to true for better numerical performance (it reduces startup transients).

rhoinf specifies the numerical damping parameter (spectral radius of the amplification matrix) in the range of $$[0.0,1.0]$$ used in the generalized-$$\alpha$$ time integrator implemented in BeamDyn for dynamic analysis. For rhoinf = 1.0, no numerical damping is introduced and the generalized-$$\alpha$$ scheme is identical to the Newmark scheme; for rhoinf = 0.0, maximum numerical damping is introduced. Numerical damping may help produce numerically stable solutions.

Quadrature specifies the spatial numerical integration scheme. There are two options: 1) Gauss quadrature; and 2) Trapezoidal quadrature. We note that in the current version, Gauss quadrature is implemented in reduced form to improve efficiency and avoid shear locking. In the trapezoidal quadrature, only one member (FE element) can be defined in the following GEOMETRY section of the primary input file. Trapezoidal quadrature is appropriate when the number of “blade input stations” (described below) is significantly greater than the order of the LSFE.

Refine specifies a refinement parameter used in trapezoidal quadrature. An integer value greater than unity will split the space between two input stations into “Refine factor” of segments. The keyword “DEFAULT” may be used to set it to 1, i.e., no refinement is needed. This entry is not used in Gauss quadrature.

N_Fact specifies a parameter used in the modified Newton-Raphson scheme. If N_Fact = 1 a full Newton iteration scheme is used, i.e., the global tangent stiffness matrix is computed and factorized at each iteration; if N_Fact > 1 a modified Newton iteration scheme is used, i.e., the global stiffness matrix is computed and factorized every N_Fact iterations within each time step. The keyword “DEFAULT” sets N_Fact = 5.

DTBeam specifies the constant time increment of the time-integration in seconds. The keyword “DEFAULT” may be used to indicate that the module should employ the time increment prescribed by the driver code (FAST/stand-alone driver program).

load_retries specifies the maximum number of load retries allowed. This option currently works only for static analysis. For every load retry, the applied load is halved to promote convergence of the Newton-Raphson scheme in iteration of smaller load steps as opposed to one single large load step which may cause divergence of the Newton-Raphson scheme. The keyword “DEFAULT” sets load_retries = 20.

NRMax specifies the maximum number of iterations per time step in the Newton-Raphson scheme. If convergence is not reached within this number of iterations, BeamDyn returns an error message and terminates the simulation. The keyword “DEFAULT” sets NRMax = 10.

Stop_Tol specifies a tolerance parameter used in convergence criteria of a nonlinear solution that is used for the termination of the iteration. The keyword “DEFAULT” sets Stop_Tol = 1.0E-05. Please refer to Section 4.2.4.5.7 for more details.

tngt_stf_fd is a boolean that sets the flag to compute the tangent stiffness matrix using finite differencing instead of analytical differentiation. The finite differencing is performed using a central scheme. The keyword “DEFAULT” sets tngt_stf_fd = FALSE.

tngt_stf_comp is a boolean that sets the flag to compare the analytical tangent stiffness matrix against the finite differenced tangent stiffness matrix. Information is written to the terminal regarding the dof where the maximum difference is observed. If tngt_stf_fd = FALSE and tngt_stf_comp = TRUE, the analytical tangent stiffness matrix is used to solve the system of equations while the finite difference tangent stiffness matrix is used only to perform the comparison of the two matrices. The keyword “DEFAULT” sets tngt_stf_comp = FALSE.

tngt_stf_pert sets the perturbation size for finite differencing. The “DEFAULT” value based on experience is set to 1e-06.

tngt_stf_difftol is the maximum allowable relative difference between the analytical and finite differenced tangent stiffness matrices. If for any entry in the matrices, the relative difference exceeds this value the simulation will terminate. The “DEFAULT” value is currently set to 1e-01.

RotStates is a flag that indicates if BeamDyn’s continuous states should be oriented in the rotating frame during linearization analysis when coupled to OpenFAST. If multi-blade coordinate (MBC3) analysis is performed, RotStates must be true.

### 4.2.4.3.3.2. Geometry Parameter¶

The blade geometry is defined by a curvilinear local blade reference axis. The blade reference axis locates the origin and orientation of each a local coordinate system where the cross-sectional 6x6 stiffness and mass matrices are defined in the BeamDyn blade input file. It should not really matter where in the cross section the 6x6 stiffness and mass matrices are defined relative to, as long as the reference axis is consistently defined and closely follows the natural geometry of the blade.

The blade beam model is composed of several members in contiguous series and each member is defined by at least three key points in BeamDyn. A cubic-spline-fit pre-processor implemented in BeamDyn automatically generates the member based on the key points and then interconnects the members into a blade. There is always a shared key point at adjacent members; therefore the total number of key points is related to number of members and key points in each member.

member_total specifies the total number of beam members used in the structure. With the LSFE discretization, a single member and a sufficiently high element order, order_elem below, may well be sufficient.

kp_total specifies the total number of key points used to define the beam members.

The following section contains member_total lines. Each line has two integers providing the member number (must be 1, 2, 3, etc., sequentially) and the number of key points in this member, respectively. It is noted that the number of key points in each member is not independent of the total number of key points and they should satisfy the following equality:

(4.59)$kp\_total = \sum_{i=1}^{member\_total} n_i - member\_total +1$

where $$n_i$$ is the number of key points in the $$i^{th}$$ member. Because cubic splines are implemented in BeamDyn, $$n_i$$ must be greater than or equal to three. Figures Fig. 4.26 and Fig. 4.27 show two cases for member and key-point definition.

Fig. 4.26 Member and key point definition: one member defined by four key points;

Fig. 4.27 Member and key point definition: two members defined by six key points.

The next section defines the key-point information, preceded by two header lines. Each key point is defined by three physical coordinates (kp_xr, kp_yr, kp_zr) in the IEC standard blade coordinate system (the blade reference coordinate system) along with a structural twist angle (initial_twist) in the unit of degrees. The structural twist angle is also following the IEC standard which is defined as the twist about the negative $$Z_l$$ axis. The key points are entered sequentially (from the root to tip) and there should be a total of kp_total lines for BeamDyn to read in the information, after two header lines. Please refer to Fig. 4.28 for more details on the blade geometry definition.

Fig. 4.28 BeamDyn Blade Geometry - Top: Side View; Middle: Front View (Looking Downwind); Bottom: Cross Section View (Looking Toward the Tip, from the Root)

### 4.2.4.3.3.3. Mesh Parameter¶

Order_Elem specifies the order of shape functions for each finite element. Each LSFE will have Order_Elem+1 nodes located at the GLL quadrature points. All LSFEs will have the same order. With the LSFE discretization, an increase in accuracy will, in general, be better achieved by increasing Order_Elem (i.e., $$p$$-refinement) rather than increasing the number of members (i.e., $$h$$-refinement). For Gauss quadrature, Order_Elem should be greater than one.

### 4.2.4.3.3.4. Material Parameter¶

BldFile is the file name of the blade input file. This name should be in quotations and can contain an absolute path or a relative path.

### 4.2.4.3.3.5. Pitch Actuator Parameter¶

In this release, the pitch actuator implemented in BeamDyn is not available. The UsePitchAct should be set to “FALSE” in this version, whereby the input blade-pitch angle prescribed by the driver code is used to orient the blade directly. PitchJ, PitchK, and PitchC specify the pitch actuator inertial, stiffness, and damping coefficient, respectively. In future releases, specifying UsePitchAct $$=$$ TRUE will enable a second-order pitch actuator, whereby the pitch angular orientation, velocity, and acceleration are determined by the actuator based on the input blade-pitch angle prescribed by the driver code.

### 4.2.4.3.3.6. Outputs¶

In this section of the primary input file, the user sets flags and switches for the desired output behavior.

Specifying SumPrint = TRUE causes BeamDyn to generate a summary file with name InputFile.sum. See Section 4.2.4.4.2 for summary file details.

OutFmt parameter controls the formatting of the results within the stand-alone BeamDyn output file. It needs to be a valid Fortran format string, but BeamDyn currently does not check the validity. This input is unused when BeamDyn is used coupled to FAST.

NNodeOuts specifies the number of nodes where output can be written to a file. Currently, BeamDyn can output quantities at a maximum of nine nodes.

OutNd is a list NNodeOuts long of node numbers between 1 and the number of nodes on the output mesh, separated by any combination of commas, semicolons, spaces, and/or tabs. The nodal positions are given in the summary file, if output. For Gassian quadrature, the number of nodes on the output mesh is the total number of FE nodes; for trapezoidal quadrature, this is the number of quadrature nodes.

The OutList block contains a list of output parameters. Enter one or more lines containing quoted strings that in turn contain one or more output parameter names. Separate output parameter names by any combination of commas, semicolons, spaces, and/or tabs. If you prefix a parameter name with a minus sign, “-“, underscore, “_”, or the characters “m” or “M”, BeamDyn will multiply the value for that channel by -1 before writing the data. The parameters are written in the order they are listed in the input file. BeamDyn allows you to use multiple lines so that you can break your list into meaningful groups and so the lines can be shorter. You may enter comments after the closing quote on any of the lines. Entering a line with the string “END” at the beginning of the line or at the beginning of a quoted string found at the beginning of the line will cause BeamDyn to quit scanning for more lines of channel names. Node-related quantities are generated for the requested nodes identified through the OutNd list above. If BeamDyn encounters an unknown/invalid channel name, it warns the users but will remove the suspect channel from the output file. Please refer to Appendix Section 4.2.4.8.2 for a complete list of possible output parameters and their names.

### 4.2.4.3.3.7. Nodal Outputs¶

In addition to the named outputs in Section 4.2.4.3.3.6 above, BeamDyn allows for outputting the full set blade node motions and loads (tower nodes unavailable at present). Please refer to the BeamDyn_Nodes tab in the Excel file OutListParameters.xlsx for a complete list of possible output parameters.

This section follows the END statement from normal Outputs section described above, and includes a separator description line followed by the following optinos.

BldNd_BlOutNd specifies which nodes to output. This is currently unused.

The OutList section controls the nodal output quantities generated by BeamDyn. In this section, the user specifies the name of the channel family to output. The output name for each channel is then created internally by BeamDyn by combining the blade number, node number, and channel family name. For example, if the user specifies TDxr as the channel family name, the output channels will be named with the convention of B$$\mathbf{\beta}$$N###TDxr where $$\mathbf{\beta}$$ is the blade number, and ### is the three digit node number.

#### 4.2.4.3.3.7.1. Sample Nodal Outputs section¶

This sample includes the END statement from the regular outputs section.

  1END of input file (the word "END" must appear in the first 3 columns of this last OutList line)
2---------------------- NODE OUTPUTS --------------------------------------------
4              OutList     - The next line(s) contains a list of output parameters.  See OutListParameters.xlsx, BeamDyn_Nodes tab for a listing of available output channels, (-)
5"FxL"       - Sectional force resultants at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N)
6"FyL"       - Sectional force resultants at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N)
7"FzL"       - Sectional force resultants at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N)
8"MxL"       - Sectional moment resultants at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N-m)
9"MyL"       - Sectional moment resultants at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N-m)
10"MzL"       - Sectional moment resultants at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N-m)
11"Fxr"       - Sectional force resultants at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system    (N)
12"Fyr"       - Sectional force resultants at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system    (N)
13"Fzr"       - Sectional force resultants at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system    (N)
14"Mxr"       - Sectional moment resultants at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system    (N-m)
15"Myr"       - Sectional moment resultants at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system    (N-m)
16"Mzr"       - Sectional moment resultants at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system    (N-m)
17"TDxr"      - Sectional translational deflection (relative to the undeflected position) at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system    (m)
18"TDyr"      - Sectional translational deflection (relative to the undeflected position) at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system    (m)
19"TDzr"      - Sectional translational deflection (relative to the undeflected position) at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system    (m)
20"RDxr"      - Sectional angular/rotational deflection Wiener-Milenkovic parameter (relative to the undeflected orientation) at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system    (-)
21"RDyr"      - Sectional angular/rotational deflection Wiener-Milenkovic parameter (relative to the undeflected orientation) at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system    (-)
22"RDzr"      - Sectional angular/rotational deflection Wiener-Milenkovic parameter (relative to the undeflected orientation) at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system    (-)
23"AbsXg"     - Node position in X (global coordinate)     g: the global inertial frame coordinate system; when coupled to FAST, this is equivalent to FAST’s global inertial frame (i) coordinate system     (m)
24"AbsYg"     - Node position in Y (global coordinate)     g: the global inertial frame coordinate system; when coupled to FAST, this is equivalent to FAST’s global inertial frame (i) coordinate system     (m)
25"AbsZg"     - Node position in Z (global coordinate)     g: the global inertial frame coordinate system; when coupled to FAST, this is equivalent to FAST’s global inertial frame (i) coordinate system     (m)
26"AbsXr"     - Node position in X (relative to root)     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (m)
27"AbsYr"     - Node position in Y (relative to root)     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (m)
28"AbsZr"     - Node position in Z (relative to root)     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (m)
29"TVxg"      - Sectional translational velocities (absolute)    g: the global inertial frame coordinate system; when coupled to FAST, this is equivalent to FAST’s global inertial frame (i) coordinate system     (m/s)
30"TVyg"      - Sectional translational velocities (absolute)    g: the global inertial frame coordinate system; when coupled to FAST, this is equivalent to FAST’s global inertial frame (i) coordinate system     (m/s)
31"TVzg"      - Sectional translational velocities (absolute)    g: the global inertial frame coordinate system; when coupled to FAST, this is equivalent to FAST’s global inertial frame (i) coordinate system     (m/s)
32"TVxl"      - Sectional translational velocities (absolute)    l: a floating coordinate system local to the deflected beam    (m/s)
33"TVyl"      - Sectional translational velocities (absolute)    l: a floating coordinate system local to the deflected beam    (m/s)
34"TVzl"      - Sectional translational velocities (absolute)    l: a floating coordinate system local to the deflected beam    (m/s)
35"TVxr"      - Sectional translational velocities (absolute)    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (m/s)
36"TVyr"      - Sectional translational velocities (absolute)    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (m/s)
37"TVzr"      - Sectional translational velocities (absolute)    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (m/s)
38"RVxg"      - Sectional angular/rotational velocities (absolute)    g: the global inertial frame coordinate system; when coupled to FAST, this is equivalent to FAST’s global inertial frame (i) coordinate system     (deg/s)
39"RVyg"      - Sectional angular/rotational velocities (absolute)    g: the global inertial frame coordinate system; when coupled to FAST, this is equivalent to FAST’s global inertial frame (i) coordinate system     (deg/s)
40"RVzg"      - Sectional angular/rotational velocities (absolute)    g: the global inertial frame coordinate system; when coupled to FAST, this is equivalent to FAST’s global inertial frame (i) coordinate system     (deg/s)
41"RVxl"      - Sectional angular/rotational velocities (absolute)    l: a floating coordinate system local to the deflected beam    (deg/s)
42"RVyl"      - Sectional angular/rotational velocities (absolute)    l: a floating coordinate system local to the deflected beam    (deg/s)
43"RVzl"      - Sectional angular/rotational velocities (absolute)    l: a floating coordinate system local to the deflected beam    (deg/s)
44"RVxr"      - Sectional angular/rotational velocities (absolute)    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (deg/s)
45"RVyr"      - Sectional angular/rotational velocities (absolute)    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (deg/s)
46"RVzr"      - Sectional angular/rotational velocities (absolute)    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (deg/s)
47"TAxl"      - Sectional angular/rotational velocities (absolute)    l: a floating coordinate system local to the deflected beam    (m/s^2)
48"TAyl"      - Sectional angular/rotational velocities (absolute)    l: a floating coordinate system local to the deflected beam    (m/s^2)
49"TAzl"      - Sectional angular/rotational velocities (absolute)    l: a floating coordinate system local to the deflected beam    (m/s^2)
50"TAxr"      - Sectional angular/rotational velocities (absolute)    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (m/s^2)
51"TAyr"      - Sectional angular/rotational velocities (absolute)    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (m/s^2)
52"TAzr"      - Sectional angular/rotational velocities (absolute)    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (m/s^2)
53"RAxl"      - Sectional angular/rotational velocities (absolute)    l: a floating coordinate system local to the deflected beam    (deg/s^2)
54"RAyl"      - Sectional angular/rotational velocities (absolute)    l: a floating coordinate system local to the deflected beam    (deg/s^2)
55"RAzl"      - Sectional angular/rotational velocities (absolute)    l: a floating coordinate system local to the deflected beam    (deg/s^2)
56"RAxr"      - Sectional angular/rotational velocities (absolute)    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (deg/s^2)
57"RAyr"      - Sectional angular/rotational velocities (absolute)    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (deg/s^2)
58"RAzr"      - Sectional angular/rotational velocities (absolute)    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (deg/s^2)
59"PFxL"      - Applied point forces at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N)
60"PFyL"      - Applied point forces at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N)
61"PFzL"      - Applied point forces at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N)
62"PMxL"      - Applied point moments at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N-m)
63"PMyL"      - Applied point moments at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N-m)
64"PMzL"      - Applied point moments at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N-m)
65"DFxL"      - Applied distributed forces at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N/m)
66"DFyL"      - Applied distributed forces at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N/m)
67"DFzL"      - Applied distributed forces at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N/m)
68"DMxL"      - Applied distributed moments at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N-m/m)
69"DMyL"      - Applied distributed moments at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N-m/m)
70"DMzL"      - Applied distributed moments at each node expressed in l    l: a floating coordinate system local to the deflected beam    (N-m/m)
71"DFxR"      - Applied distributed forces at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N/m)
72"DFyR"      - Applied distributed forces at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N/m)
73"DFzR"      - Applied distributed forces at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N/m)
74"DMxR"      - Applied distributed forces at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m/m)
75"DMyR"      - Applied distributed forces at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m/m)
76"DMzR"      - Applied distributed forces at each node expressed in r    r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m/m)
77"FFbxl"     - Gyroscopic force x     l: a floating coordinate system local to the deflected beam    (N)
78"FFbyl"     - Gyroscopic force y     l: a floating coordinate system local to the deflected beam    (N)
79"FFbzl"     - Gyroscopic force z     l: a floating coordinate system local to the deflected beam    (N)
80"FFbxr"     - Gyroscopic force x     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
81"FFbyr"     - Gyroscopic force y     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
82"FFbzr"     - Gyroscopic force z     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
83"MFbxl"     - Gyroscopic moment about x     l: a floating coordinate system local to the deflected beam    (N-m)
84"MFbyl"     - Gyroscopic moment about y     l: a floating coordinate system local to the deflected beam    (N-m)
85"MFbzl"     - Gyroscopic moment about z     l: a floating coordinate system local to the deflected beam    (N-m)
86"MFbxr"     - Gyroscopic moment about x     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
87"MFbyr"     - Gyroscopic moment about y     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
88"MFbzr"     - Gyroscopic moment about z     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
89"FFcxl"     - Elastic restoring force Fc x     l: a floating coordinate system local to the deflected beam    (N)
90"FFcyl"     - Elastic restoring force Fc y     l: a floating coordinate system local to the deflected beam    (N)
91"FFczl"     - Elastic restoring force Fc z     l: a floating coordinate system local to the deflected beam    (N)
92"FFcxr"     - Elastic restoring force Fc x     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
93"FFcyr"     - Elastic restoring force Fc y     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
94"FFczr"     - Elastic restoring force Fc z     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
95"MFcxl"     - Elastic restoring moment Fc about x     l: a floating coordinate system local to the deflected beam    (N-m)
96"MFcyl"     - Elastic restoring moment Fc about y     l: a floating coordinate system local to the deflected beam    (N-m)
97"MFczl"     - Elastic restoring moment Fc about z     l: a floating coordinate system local to the deflected beam    (N-m)
98"MFcxr"     - Elastic restoring moment Fc about x     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
99"MFcyr"     - Elastic restoring moment Fc about y     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
100"MFczr"     - Elastic restoring moment Fc about z     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
101"FFdxl"     - Elastic restoring force Fd x     l: a floating coordinate system local to the deflected beam    (N)
102"FFdyl"     - Elastic restoring force Fd y     l: a floating coordinate system local to the deflected beam    (N)
103"FFdzl"     - Elastic restoring force Fd z     l: a floating coordinate system local to the deflected beam    (N)
104"FFdxr"     - Elastic restoring force Fd x     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
105"FFdyr"     - Elastic restoring force Fd y     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
106"FFdzr"     - Elastic restoring force Fd z     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
107"MFdxl"     - Elastic restoring moment Fd about x     l: a floating coordinate system local to the deflected beam    (N-m)
108"MFdyl"     - Elastic restoring moment Fd about y     l: a floating coordinate system local to the deflected beam    (N-m)
109"MFdzl"     - Elastic restoring moment Fd about z     l: a floating coordinate system local to the deflected beam    (N-m)
110"MFdxr"     - Elastic restoring moment Fd about x     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
111"MFdyr"     - Elastic restoring moment Fd about y     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
112"MFdzr"     - Elastic restoring moment Fd about z     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
113"FFgxl"     - Gravity force x     l: a floating coordinate system local to the deflected beam    (N)
114"FFgyl"     - Gravity force y     l: a floating coordinate system local to the deflected beam    (N)
115"FFgzl"     - Gravity force z     l: a floating coordinate system local to the deflected beam    (N)
116"FFgxr"     - Gravity force x     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
117"FFgyr"     - Gravity force y     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
118"FFgzr"     - Gravity force z     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
119"MFgxl"     - Gravity moment about x     l: a floating coordinate system local to the deflected beam    (N-m)
120"MFgyl"     - Gravity moment about y     l: a floating coordinate system local to the deflected beam    (N-m)
121"MFgzl"     - Gravity moment about z     l: a floating coordinate system local to the deflected beam    (N-m)
122"MFgxr"     - Gravity moment about x     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
123"MFgyr"     - Gravity moment about y     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
124"MFgzr"     - Gravity moment about z     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
125"FFixl"     - Inertial force x     l: a floating coordinate system local to the deflected beam    (N)
126"FFiyl"     - Inertial force y     l: a floating coordinate system local to the deflected beam    (N)
127"FFizl"     - Inertial force z     l: a floating coordinate system local to the deflected beam    (N)
128"FFixr"     - Inertial force x     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
129"FFiyr"     - Inertial force y     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
130"FFizr"     - Inertial force z     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N)
131"MFixl"     - Inertial moment about x     l: a floating coordinate system local to the deflected beam    (N-m)
132"MFiyl"     - Inertial moment about y     l: a floating coordinate system local to the deflected beam    (N-m)
133"MFizl"     - Inertial moment about z     l: a floating coordinate system local to the deflected beam    (N-m)
134"MFixr"     - Inertial moment about x     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
135"MFiyr"     - Inertial moment about y     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
136"MFizr"     - Inertial moment about z     r: a floating reference coordinate system fixed to the root of the moving beam; when coupled to FAST for blades, this is equivalent to the IEC blade (b) coordinate system     (N-m)
137END of input file (the word "END" must appear in the first 3 columns of this last OutList line)
138---------------------------------------------------------------------------------------


The blade input file defines the cross-sectional properties at various stations along a blade and six damping coefficient for the whole blade. A sample BeamDyn blade input file is given in Section 4.2.4.8. The blade input file begins with two lines of header information, which is for the user but is not used by the software.

Station_Total specifies the number cross-sectional stations along the blade axis used in the analysis.

Damp_Type specifies if structural damping is considered in the analysis. If Damp_Type = 0, then no damping is considered in the analysis and the six damping coefficient in the next section will be ignored. If Damp_Type = 1, structural damping will be included in the analysis.

### 4.2.4.3.4.2. Damping Coefficient¶

This section specifies six damping coefficients, $$\mu_{ii}$$ with $$i \in [1,6]$$, for six DOFs (three translations and three rotations). Viscous damping is implemented in BeamDyn where the damping forces are proportional to the strain rate. These are stiffness-proportional damping coefficients, whereby the $$6\times6$$ damping matrix at each cross section is scaled from the $$6 \times 6$$ stiffness matrix by these diagonal entries of a $$6 \times 6$$ scaling matrix:

(4.60)$\mathcal{\underline{F}}^{Damp} = \underline{\underline{\mu}}~\underline{\underline{S}}~\dot{\underline{\epsilon}}$

where $$\mathcal{\underline{F}}^{Damp}$$ is the damping force, $$\underline{\underline{S}}$$ is the $$6 \times 6$$ cross-sectional stiffness matrix, $$\dot{\underline{\epsilon}}$$ is the strain rate, and $$\underline{\underline{\mu}}$$ is the damping coefficient matrix defined as

(4.61)$\begin{split}\underline{\underline{\mu}} = \begin{bmatrix} \mu_{11} & 0 & 0 & 0 & 0 & 0 \\ 0 & \mu_{22} & 0 & 0 & 0 & 0 \\ 0 & 0 & \mu_{33} & 0 & 0 & 0 \\ 0 & 0 & 0 & \mu_{44} & 0 & 0 \\ 0 & 0 & 0 & 0 & \mu_{55} & 0 \\ 0 & 0 & 0 & 0 & 0 & \mu_{66} \\ \end{bmatrix}\end{split}$

### 4.2.4.3.4.3. Distributed Properties¶

This section specifies the cross-sectional properties at each of the Station_Total stations. For each station, a non-dimensional parameter $$\eta$$ specifies the station location along the local blade reference axis ranging from $$[0.0,1.0]$$. The first and last station parameters must be set to $$0.0$$ (for the blade root) and $$1.0$$ (for the blade tip), respectively.

Following the station location parameter $$\eta$$, there are two $$6 \times 6$$ matrices providing the structural and inertial properties for this cross-section. First is the stiffness matrix and then the mass matrix. We note that these matrices are defined in a local coordinate system along the blade axis with $$Z_{l}$$ directing toward the unit tangent vector of the blade reference axis. For a cross-section without coupling effects, for example, the stiffness matrix is given as follows:

(4.62)$\begin{split}\begin{bmatrix} K_{ShrFlp} & 0 & 0 & 0 & 0 & 0 \\ 0 & K_{ShrEdg} & 0 & 0 & 0 & 0 \\ 0 & 0& EA & 0 & 0 & 0 \\ 0 & 0 & 0 & EI_{Edg} & 0 & 0 \\ 0 & 0 & 0 & 0 & EI_{Flp} & 0 \\ 0 & 0 & 0 & 0 & 0 & GJ \end{bmatrix}\end{split}$

where $$K_{ShrEdg}$$ and $$K_{ShrFlp}$$ are the edge and flap shear stiffnesses, respectively; $$EA$$ is the extension stiffness; $$EI_{Edg}$$ and $$EI_{Flp}$$ are the edge and flap stiffnesses, respectively; and $$GJ$$ is the torsional stiffness. It is pointed out that for a generic cross-section, the sectional property matrices can be derived from a sectional analysis tool, e.g. VABS, BECAS, or NuMAD/BPE.

A generalized sectional mass matrix is given by:

(4.63)$\begin{split}\begin{bmatrix} m & 0 & 0 & 0 & 0 & -m Y_{cm} \\ 0 & m & 0 & 0 & 0 & m X_{cm}\\ 0 & 0& m & m Y_{cm} & -m X_{cm} & 0 \\ 0 & 0 & m Y_{cm} & i_{Edg} & -i_{cp} & 0 \\ 0 & 0 &-m X_{cm} & -i_{cp} & i_{Flp} & 0 \\ -m Y_{cm} & m X_{cm} & 0 & 0 & 0 & i_{plr} \end{bmatrix}\end{split}$

where $$m$$ is the mass density per unit span; $$X_{cm}$$ and $$Y_{cm}$$ are the local coordinates of the sectional center of mass, respectively; $$i_{Edg}$$ and $$i_{Flp}$$ are the edge and flap mass moments of inertia per unit span, respectively; $$i_{plr}$$ is the polar moment of inertia per unit span; and $$i_{cp}$$ is the sectional cross-product of inertia per unit span. We note that for beam structure, the $$i_{plr}$$ is given as (although this relationship is not checked by BeamDyn)

(4.64)$i_{plr} = i_{Edg} + i_{Flp}$